raghead
02-01-2008, 03:35 PM
Materials
A Bottle of Nasal Spray
A Bowl (I used a vertical feed from a paintball gun)
A screen (I made one out of tin foil)
Scissors
A knife
A small plug (optional)
A rubber band
Instructions
1. Take the colored cap off the Nasal Spray
http://img81.imageshack.us/img81/8726/97717093lt5.jpg
2. Take the top piece off of the bottle
http://img86.imageshack.us/img86/9946/58243301rb4.jpg
3. Cut the top of the piece off. Another piece of plastic should fall out. (I know I have a knife in the picture, but I recommend using scissors as it is a bitch to cut)
http://img220.imageshack.us/img220/2067/96525608ni6.jpg
4. Take off the middle piece of the Nasal Spray.
http://img230.imageshack.us/img230/4301/80447891uj9.jpg
5. Cut out the inside of it. This part is pretty fucking hard, but keep trying and it will eventually cut.
http://img352.imageshack.us/img352/6282/69387987qs2.jpg
6. Carve a hole at the bottom of the bottle just big enough for the top piece to fit into. Try not to make it too big.
http://img230.imageshack.us/img230/411/52623837ez5.jpg
It should look like this if you have done it right so far:
http://img215.imageshack.us/img215/2605/86325822wy9.jpg
7. Put your bowl piece on the wide part of the top piece.
http://img223.imageshack.us/img223/3778/11ip3.jpg
8. Fasten the bowl with something, I used a rubber band.
http://img223.imageshack.us/img223/8162/12gh7.jpg
9. Fill with enough water so that when you suck through it, it bubbles, but no water gets in your mouth (it helps if you tilt it towards the bowl).
10. Put on your screen and toke up. (I made my screen out of aluminum foil)
http://img82.imageshack.us/img82/2372/13kg9.jpg
Optional
If you are using this as a stealth piece, you might want to follow these steps:
1. Take a bottle of contact solution or something with a similar cap.
http://img215.imageshack.us/img215/944/72083227rl9.jpg
2. Take the cap off
3. Cut off the top of the cap
http://img227.imageshack.us/img227/8797/74924660zh5.jpg
4. Plug the hole in the bottle with the cap when you're not using the piece. This makes the hole a lot less obvious.
http://img223.imageshack.us/img223/7221/10ii4.jpg
(this is my entry for the most creative home piece contest, if one of the mods decides to start it. I did not steal this idea from anywhere, I came up with it myself)
A Bottle of Nasal Spray
A Bowl (I used a vertical feed from a paintball gun)
A screen (I made one out of tin foil)
Scissors
A knife
A small plug (optional)
A rubber band
Instructions
1. Take the colored cap off the Nasal Spray
http://img81.imageshack.us/img81/8726/97717093lt5.jpg
2. Take the top piece off of the bottle
http://img86.imageshack.us/img86/9946/58243301rb4.jpg
3. Cut the top of the piece off. Another piece of plastic should fall out. (I know I have a knife in the picture, but I recommend using scissors as it is a bitch to cut)
http://img220.imageshack.us/img220/2067/96525608ni6.jpg
4. Take off the middle piece of the Nasal Spray.
http://img230.imageshack.us/img230/4301/80447891uj9.jpg
5. Cut out the inside of it. This part is pretty fucking hard, but keep trying and it will eventually cut.
http://img352.imageshack.us/img352/6282/69387987qs2.jpg
6. Carve a hole at the bottom of the bottle just big enough for the top piece to fit into. Try not to make it too big.
http://img230.imageshack.us/img230/411/52623837ez5.jpg
It should look like this if you have done it right so far:
http://img215.imageshack.us/img215/2605/86325822wy9.jpg
7. Put your bowl piece on the wide part of the top piece.
http://img223.imageshack.us/img223/3778/11ip3.jpg
8. Fasten the bowl with something, I used a rubber band.
http://img223.imageshack.us/img223/8162/12gh7.jpg
9. Fill with enough water so that when you suck through it, it bubbles, but no water gets in your mouth (it helps if you tilt it towards the bowl).
10. Put on your screen and toke up. (I made my screen out of aluminum foil)
http://img82.imageshack.us/img82/2372/13kg9.jpg
Optional
If you are using this as a stealth piece, you might want to follow these steps:
1. Take a bottle of contact solution or something with a similar cap.
http://img215.imageshack.us/img215/944/72083227rl9.jpg
2. Take the cap off
3. Cut off the top of the cap
http://img227.imageshack.us/img227/8797/74924660zh5.jpg
4. Plug the hole in the bottle with the cap when you're not using the piece. This makes the hole a lot less obvious.
http://img223.imageshack.us/img223/7221/10ii4.jpg
(this is my entry for the most creative home piece contest, if one of the mods decides to start it. I did not steal this idea from anywhere, I came up with it myself)